120度矩形波モードでの運転はスムーズそのもの。電源電圧30Vまで上げてみると4000rpmで軽快に回っている。。。そろそろ決断しよう。
そういや、新規購入のロータ。ロータがブレてて振動がひどい。どうしたものか。
昨日やっと巻線が完了し、8sqのケーブル(ごつくて硬い)を半田づけ完了。モータコントローラ一式を車両から下ろして、テストベンチを組んでみた。
安定化電源を20V 2A制限にセットして、120度矩形波駆動で、恐る恐る回してみる。お〜ちゃんと回る。。巻線は成功。さて、電流制限を20AにUpして、120度矩形波駆動でDuty広げていくと、、3200rpm程度で回る。狙い通りのところに落ち着いている。OK。
さて、180度正弦波のベクトル制御で回してみよう。。あ〜、PI制御が破綻している。3000rpm超えるところまで回っているが、あかん。今日はもう晩御飯にしよう。。20:30。
明日はオシロに電流センサ繋いで何が起きてるかチェック。。低損失コア変更が原因なのか、巻き数を減らしたのが原因なのか、そもそも制御周期が間に合ってないのか、、さてはて。最後のだと、やだな(そんな時のために、RX62Tのボードは用意してあるけど、プログラム移植が間に合ってない)。
AKIBA Watchみてたら、、Pirate Radioがツクモで扱いはじめました〜とか、気の狂ったかのような360個ものSMD LEDを手半田づけ必要な「TEEN CIRCLE」キットとか紹介されてるじゃないですか。早速、定時のチャイム後に、電車に飛び乗って、買い出しに出かけたのでした。
晩飯のピザも買い出して、食事を満喫したあと、組み立てに入るのだ、、Pirate Radioからね。。完成〜。結構良い音してるね〜。
来たる6/24(日)、筑波サーキットにてCQ EVミニカートのレースが開催される。。ので、エントリーしました。エントリーするからには、勝ちに行かねばなのだが。。2017年のレースで低損失コアをいただきましたので、、いざ、巻線。やっと巻線。このコア、磁気回路的に対称。ノーマルコアは、ビス止めするために、切り欠き多数、穴位置も非対称。このあたりも調子良さに繋がるのか? まだ巻き巻き中なので、感触わからず。
さてー、お天気、どうなるかな〜。あちこち予約して、乗り込む準備OK〜
結局、OSをUbuntu 18.04 LTSのDesktopからServerにスイッチ。GUI環境いらんわ。設定デフォルトが違うわということで。おっと、pppoeがセッション数過多で繋がらない。。か
そーいえば、LANケーブルの買い置きが枯渇してたっけ。近くのヤマダ電気に買いにでかける。ELECOMのCAT5eケーブルを買い込んで帰る(素線買い込んで加工するより安価なのは笑った)。1000BASE-Tで使うからCat5eで十分。10GbE行くにはCAT6以降が必要ですね。。ま、うちにはまだまだ先ですな。10G。
読書してて、作業はすすまず。この日記も書いてるしね。。
実家のおうちサーバをリニューアルしようと、構成検討開始したのが、昨日。歴代のCPUは、VIAのC7 1.5GHz 1Core、Intel Atom D525 1.8GHz 4core。次はどうするか? Intel Core i Gen.8thが使ってみたいけど、どーしよ。省電力Coreだと、Intel Pentium Silver J5005 1.5GHz 4core搭載のM/BがASRockから出ているけど、、OnBoard GbE x1、PCIe 2.0 x1 laneしか搭載しておらず。
ルーティングやらなにやらで3portのGbEが必要で、PCIe x4なNICを搭載しようとすると、PCIe 2.0 x1では帯域不足が懸念される。ボツ。
さて、そうすると、4core以上は使いたいとの野望もあり、Core i3 or i5が視野に入ってくる。CeleronやPentiumは2core止まりだから却下。Core i3 8100は、3.6GHzでTDP 65W! Turbo Boostには非対応。Core i5 8400 2.8GHz 6coreは Turbo Boostに対応している。どこまでCLK下げられるかは、情報ひっかからない。上がる方向は色々記事あるんだけどね〜。Core i Gen.8用のM/Bには、Intel GbE が2port乗っているものがありますな。ちっさい筐体にしたいので、Mini-ITXなM/Bを検討してるけど、ちゃんと存在する。ASRockとかGigaByteとかから出てる。今回、AMDのRyzenは眼中にないのよ〜。
GbEのPortを追加したいけど、リーズナブルなNICが無いのね。。x2 or x4が欲しいけど、、新品がだめなら中古か。ということで、探すと秋葉原に存在。平日しかOpenしてない。。
ということで、NICから購入。おっとへ突入。ショールームが事務所になってて、、みなさんパタパタとキーボードを叩いてらっしゃる。中古のNIC欲しいんですけど〜と、カウンターの兄さんに声をかけて、HPの2Port GbE NICをゲットしたのでした。2kちょい。
tsukumoで大人買い。ASRock Z370M-ITX/ac + Core i5-8400 + DDR4 16GB + SSD 500GB + HDD 6TB x2。。値段は言いたく無い。。tsukumoの場合、アキバで買うより、通販で買った方がお得かもしれない。
お昼をアキバのカレー屋さん(ラホール)で済ませてきたので、帰ったら早速、動作確認。初期不良あったら、即日交換に行く気まんまんね。最小構成でのOSインストールはOKで、フル構成問題無い様子。MEMTEST仕掛けて、寝るか。。
5/16深夜に実家からヘルプの電話。Macがネットに繋がらないよ〜と。って、ワインひっかけて寝てたので留守電に入ってた。結構早いおめざめだったので、リモートでGWサーバにログインしてみたけど、普通に動いてた。Uptimeが600day超える運用を素でしてるサーバなんで、また何かあったか!といろいろ調査してみた。
Atom D525で動いているこのサーバ。この日記を遡ると、、2011/4に入れ替えてたのね。そろそろHDDとかイロイロと不安になってくる年数。まるっと7年。8年目突入。いやな予感がしたので、/dev/sdbを /dev/sdcへバックアップ。tarコマンドで丸々コピー。朝チュンするまえに、寝る。
ちょっちS.M.A.R.Tチェックしてみよう。と、後日チェックした結果が以下。
[root@hagi4 log]# /usr/sbin/smartctl -a /dev/sda smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.18-419.el5] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN3220F30J68GE LU WWN Device Id: 5 000cca 369c75d7c Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sat May 19 23:04:39 2018 JST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (18238) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 134 134 054 Pre-fail Offline - 88 3 Spin_Up_Time 0x0007 163 163 024 Pre-fail Always - 428 (Average 276) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 40 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 133 133 020 Pre-fail Offline - 27 9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 62309 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 40 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 135 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 135 194 Temperature_Celsius 0x0002 157 157 000 Old_age Always - 38 (Min/Max 17/52) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 1 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 9 hours (0 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 95 d6 0e 08 03 Error: ABRT at LBA = 0x03080ed6 = 50859734 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 39 00 00 6b 0e 08 e0 08 01:57:48.011 WRITE MULTIPLE EXT 39 00 00 6b 0d 08 e0 08 01:57:47.978 WRITE MULTIPLE EXT 39 00 00 6b 0c 08 e0 08 01:57:47.945 WRITE MULTIPLE EXT 39 00 00 6b 0b 08 e0 08 01:57:47.912 WRITE MULTIPLE EXT 39 00 00 6b 0a 08 e0 08 01:57:47.878 WRITE MULTIPLE EXT SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. [root@hagi4 log]# /usr/sbin/smartctl -a /dev/sdb smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.18-419.el5] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723030ALA640 Serial Number: MK0311YHG429HA LU WWN Device Id: 5 000cca 225c1da24 Firmware Version: MKAOA3B0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sat May 19 23:05:15 2018 JST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (29271) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 65536 2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 82 3 Spin_Up_Time 0x0007 124 124 024 Pre-fail Always - 622 (Average 623) 4 Start_Stop_Count 0x0012 036 036 000 Old_age Always - 256615 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 133 133 020 Pre-fail Offline - 27 9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 62273 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 21 192 Power-Off_Retract_Count 0x0032 046 046 000 Old_age Always - 65535 193 Load_Cycle_Count 0x0012 001 001 000 Old_age Always - 256709 194 Temperature_Celsius 0x0002 162 162 000 Old_age Always - 37 (Min/Max 17/56) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. [root@hagi4 log]# /usr/sbin/smartctl -a /dev/sdc smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.18-419.el5] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723030ALA640 Serial Number: MK0311YHG5UBYA LU WWN Device Id: 5 000cca 225c2a526 Firmware Version: MKAOA580 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sat May 19 23:05:33 2018 JST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (28081) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 134 134 054 Pre-fail Offline - 87 3 Spin_Up_Time 0x0007 127 127 024 Pre-fail Always - 606 (Average 609) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 2620 5 Reallocated_Sector_Ct 0x0033 067 067 005 Pre-fail Always - 774 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 133 133 020 Pre-fail Offline - 27 9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 62155 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 16 192 Power-Off_Retract_Count 0x0032 098 098 000 Old_age Always - 2620 193 Load_Cycle_Count 0x0012 098 098 000 Old_age Always - 2620 194 Temperature_Celsius 0x0002 206 206 000 Old_age Always - 29 (Min/Max 9/53) 196 Reallocated_Event_Count 0x0032 045 045 000 Old_age Always - 1174 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 4 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 occurred at disk power-on lifetime: 33071 hours (1377 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 59 05 01 05 Error: UNC at LBA = 0x05010559 = 83952985 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 52 05 01 40 08 3d+15:50:22.413 READ FPDMA QUEUED 60 00 00 22 14 00 40 08 3d+15:50:22.406 READ FPDMA QUEUED 60 08 00 a2 05 01 40 08 3d+15:50:22.406 READ FPDMA QUEUED 60 08 00 22 15 00 40 08 3d+15:50:22.399 READ FPDMA QUEUED 60 00 00 2a 09 c0 40 08 3d+15:50:22.397 READ FPDMA QUEUED Error 3 occurred at disk power-on lifetime: 23783 hours (990 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 91 02 01 06 Error: UNC at LBA = 0x06010291 = 100729489 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 8a 02 01 40 08 1d+04:50:46.665 READ FPDMA QUEUED 60 08 00 aa 04 01 40 08 1d+04:50:46.664 READ FPDMA QUEUED 60 08 00 ba 04 01 40 08 1d+04:50:46.664 READ FPDMA QUEUED 60 08 00 9a 04 01 40 08 1d+04:50:46.654 READ FPDMA QUEUED 60 08 00 22 0c 00 40 08 1d+04:50:46.648 READ FPDMA QUEUED Error 2 occurred at disk power-on lifetime: 16351 hours (681 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 71 02 01 06 Error: UNC at LBA = 0x06010271 = 100729457 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 6a 02 01 40 08 5d+02:46:22.739 READ FPDMA QUEUED 60 08 00 42 04 41 40 08 5d+02:46:22.739 READ FPDMA QUEUED 60 08 00 42 08 41 40 08 5d+02:46:22.738 READ FPDMA QUEUED 60 08 00 1a 08 41 40 08 5d+02:46:22.738 READ FPDMA QUEUED 60 08 00 9a 08 41 40 08 5d+02:46:22.738 READ FPDMA QUEUED Error 1 occurred at disk power-on lifetime: 2070 hours (86 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 99 91 0e 40 05 Error: UNC at LBA = 0x05400e91 = 88084113 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 22 0e 40 40 08 04:58:11.964 READ FPDMA QUEUED 60 08 00 1a 04 c1 40 08 04:58:11.963 READ FPDMA QUEUED 60 08 00 0a 04 c1 40 08 04:58:11.963 READ FPDMA QUEUED 60 08 00 fa 03 c1 40 08 04:58:11.963 READ FPDMA QUEUED 60 08 00 ea 03 c1 40 08 04:58:11.962 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. [root@hagi4 log]#ちょっと、あなた、/dev/sdbの3TBちゃんが、危篤じゃありませんか!?
先日(4/28に)のamazon.comで、SENAのケースをポチったのだけど、、ケースの旅の模様はこんな感じでござい。amazon.comからTrack No.のお知らせ無く、sellerからもお手紙来ておらず。モノが届かなかったら問い合わせすっか。と呑気にかまえていたら、出し抜けに届いていたという。Order Statusでは 18,May-30,Mayなんて数字がみえてたからね〜。嬉しい誤算。.comはkindle輸入した時以来あんまり使ってなかったけど、こういう時にやっぱり便利ね〜
$19.95の商品に、$24.95の送料だった。送料高い!と思ってたけど、まぁ、許す。
んで、届いてみたブツは、iPhone5が出た時に(SENA直営店から、この時も個人輸入で)買ったモノと同じ製品なのだけど、構造がかなり改善されてた。使いやすくなってて嬉しい〜。初期型は、画面サイドの皮が内側に回り込んでいたのが、無くなってた。Hampton WalletっているModelデス。
May 9, 2018, 11:51 am Delivered JAPAN Your item was delivered in JAPAN at 11:51 am on May 9, 2018. May 9, 2018, 8:43 am Out for Delivery JAPAN May 8, 2018, 1:49 pm Arrival at Post Office JAPAN May 8, 2018, 12:20 am Processed through Facility hogefuga PORT, JAPAN May 7, 2018, 6:00 pm Held in Customs hogefuga PORT, JAPAN May 6, 2018, 3:39 pm Processed Through Facility JAPAN May 2, 2018, 3:32 pm Departed TOKYO, JAPAN May 1, 2018, 10:59 am Departed LOS ANGELES, UNITED STATES May 1, 2018, 5:22 am Arrived LOS ANGELES, UNITED STATES May 1, 2018, 3:33 am Processed Through Regional Facility LOS ANGELES CA INTERNATIONAL DISTRIBUTION CENTER May 1, 2018, 3:15 am Arrived at USPS Regional Facility LOS ANGELES CA INTERNATIONAL DISTRIBUTION CENTER May 1, 2018, 3:15 am Arrived at Regional Facility LOS ANGELES CA INTERNATIONAL DISTRIBUTION CENTER May 1, 2018, 2:00 am Accepted at USPS Origin Facility GARDEN GROVE, CA 92844 May 1, 2018 Pre-Shipment Info Sent to USPS
2015年の暮れにオーダしたMacBook Pro Retina 13inch Early 2015のバッテリが膨張してしまった。しかも、複数セルあるうちの1つだけ。常時100%充電状態で使っていた影響も大きいとは思うが、、3年持たなかった。
気が付いてからは、MagSafeコネクタの真ん中Pinをマスクして、充電しないようにして使用していた。そんななか、先日「13インチMacBook Pro(Touch Bar非搭載モデル)のバッテリー交換プログラム」を開始したとのこと。僕の使っているのはE2015だからもちろん非対象なんだけど、潜在的な不具合が内在している可能性も否定できないかなと、想定。いい機会なので、バッテリ交換をお願いしてみようと。有償交換でも20k円程度だし。ちなみに、システムレポートによると充放電回数は18でした。
無事帰還したMBP。バックアップもばっちり取ってある(Time Machine!)ので、ここでOSをHigh Sierraをクリーンインストールしようと画策して作業。バックアップからはAPL以外を戻す。こうすると、APLも最新のものをインストールし直せるし。日付がかわった頃に普段使いの環境がほぼ出来上がる。若干、APLの動きがスムーズになった気がするので、作業した甲斐があった。